







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterCabinet Refacing vs Replacement in Enterprise, NV: The Question That Actually Decides It
Choose refacing if your cabinet boxes are solid, your drawer and door layout works for how you actually cook, and you’re staying in the home fewer than five years. Choose replacement if the layout is the problem. In Enterprise’s 1990s-through-2010s tract homes, that second case is more common than the comparison guides admit. Cabinet work here typically runs $14,000-$45,000 as a full kitchen project. If you want a straight read on your own kitchen, call Groundwork Construction Co. of Enterprise at (844) 797-4406 - the assessment is free and nobody pressures you toward the bigger number.

The layout lock nobody warns you about
Refacing replaces doors, drawer fronts, veneer and hardware. It leaves the boxes exactly where they are. That sounds obvious until you think through what “exactly where they are” means in a builder-grade kitchen.
Walk into a 2001 Mountain’s Edge tract kitchen and count the compromises. Forty-two-inch uppers over a peninsula with no pantry pull-out. A single stack of shallow drawers where a deep pot drawer should be. A blind corner cabinet that swallows anything past the first six inches. None of that is a finish problem. It’s a geometry problem, and refacing preserves every inch of it for another fifteen years.
What refacing actually locks in:
- Every fixed shelf position the builder nailed in place, including the one that’s two inches too low for your stand mixer
- Hinge locations, which in older frameless boxes often can’t accommodate modern soft-close hardware without new drilling
- Opening sizes, so a 12-inch cabinet stays a 12-inch cabinet no matter what door you put on it
- Corner configurations the original installer chose for speed, not for storage
The finish is the visible layer. The layout is the layer you live with every morning. That’s the trade most refacing-versus-replacement articles skip past, and it’s the one worth twenty minutes of honest thought before you spend a dollar.
How to tell if your Enterprise boxes are worth refacing
Desert heat does specific things to cabinet boxes, and they show up in three predictable places. Our technicians have up to 12 years of experience reading these signs, and a few minutes with a flashlight will tell you most of what you need to know.
Check the toekick first
The toekick is a heat-concentration zone. It sits low, it traps warm air against the floor, and in a kitchen with west-facing glass it bakes through July and August. Look for veneer lifting away from the substrate. Small bubbles near the floor line usually mean the glue has given up, and refacing over a delaminating box is money spent on a bad foundation.
Look for swelling at the base
Monsoon moisture is rare here but it’s destructive when it arrives. A single slow leak under the sink, or water pushed in during a wash that runs toward the house, can swell particleboard at the cabinet base. Swollen board doesn’t shrink back. Press a screwdriver handle into the bottom corner near the floor - if it gives, the box is compromised.
Test the drawer slides
Dried-out slides are cosmetic and cheap to replace. Cracked or pulled-out screw holes in the box itself are a different story. In a kitchen from the early 2000s, you’ll often find the original builder used the lightest slides available, and the mounting screws have wallowed out their holes. That’s fixable, but it belongs in the estimate, not in a surprise call three weeks in.
If all three checks pass, refacing is genuinely on the table. If any of them fails, replacement starts winning on math rather than preference.

The honest financial comparison
Here’s where the two paths actually land in Enterprise’s market, using realistic project sizes rather than the stripped-down numbers you see in national cost indexes.
| Path | Typical Enterprise cost | What you get | Best for |
|---|---|---|---|
| Refacing | $4,500-$12,000 | New doors, veneer, hardware; boxes and layout unchanged | Solid boxes, working layout, shorter hold |
| KraftMaid semi-custom replacement | $15,000-$35,000 | New boxes sized to your kitchen, pull-outs, deep drawers, corner solutions | Layout changes, compromised boxes, long hold |
| Full kitchen remodel (for context) | $14,000-$45,000 | Cabinets plus counters, backsplash, island if you want one | Whole-kitchen scope |
The break-even point is narrower than most homeowners expect. Replacement becomes the smarter investment when any of three things is true: your layout needs to change, your boxes are already compromised, or you plan to stay in the home long enough that the added function pays you back. For a homeowner in Southern Highlands planning another decade in the house, semi-custom replacement that adds a pull-out pantry and a deep drawer base changes how the kitchen works, not just how it looks. For someone selling in two years with a rock-solid 2004 layout, refacing puts the money where the buyer’s eye lands and keeps the rest in your pocket.
KraftMaid’s semi-custom sizing is the piece that shifts this calculation. Builder-grade boxes came in fixed increments because the builder was optimizing for cost. KraftMaid builds to your opening, which means a pull-out shelf where there was dead space and a real drawer stack where there was a single shallow drawer. That’s function added to the same footprint, and it’s the difference between a kitchen that photographs well and one that works.
The same written guarantee on both paths
One thing doesn’t change based on which option you pick. Every cabinet project we complete is covered by the 730-Day Done Right Promise - if it’s not done right, we make it right. That two-year commitment applies to veneer adhesion on a refacing job and to door alignment and hardware function on a full KraftMaid install. Refacing isn’t a lighter-duty service with a lighter-duty warranty. We put the same workmanship guarantee behind both, in writing, because the failure points (adhesive letting go, doors drifting out of square, slides binding after a hot summer) are the same failure points regardless of how the project started.
Pricing is upfront and it’s the number you see and the number you pay. There’s no-hassle financing at 0% for 18 months, and projects over $10,000 get $1,000 off. All of it is stated before work begins, not discovered on the final invoice.
What this looks like in Enterprise kitchens
Our crews spend a lot of time in Enterprise’s master-planned subdivisions, and the cabinet questions repeat in recognizable patterns.
Mountain’s Edge builders-grade kitchens from the early 2000s
The boxes are usually sound, but the layout was optimized for construction cost. This is the classic refacing-versus-replacement fork, and the answer depends entirely on whether the homeowner can live with the original geometry.
Southern Highlands homes on a long hold
Homeowners here tend to plan on staying, which tips the math toward semi-custom replacement. Adding pull-out shelves and a real drawer base pays back in daily use, not just resale.
Foothill-edge homes with engineered fill and sloped lots
These aren’t affected by cabinets directly, but the contracting here runs to rapid new-build and custom-home permitting, and any kitchen scope that touches walls or plumbing gets scheduled against that reality. We account for that in the plan, not in a mid-project change order.
For anything beyond cabinets - full kitchens, counters, islands - our Kitchen Remodeling in Enterprise page lays out the full scope. If you’re weighing cabinet work as part of a broader remodel, the Kitchen Remodeling overview covers how cabinets fit into the whole plan. And if you’re comparing contractors for a larger project, our home page puts the full service menu in one place.
What to have ready before you call
The faster an estimator can read your kitchen, the faster you get a real number instead of a range. Before the call, take photos of the inside of two or three base cabinets with the doors open, measure the length of your cabinet run, and note whether your boxes are framed or frameless. That’s a five-minute task that saves a second visit. A live person answers the phone 24 hours a day, seven days a week, so you’re never stuck with voicemail or waiting until Monday. Background-checked technicians arrive in uniform, and the estimate is free.
FAQs
Refacing is the cheaper path in Enterprise, typically $4,500-$12,000 versus $15,000-$35,000 for KraftMaid semi-custom replacement. The cheaper option is only the better investment when your boxes are solid and your layout works. Call (844) 797-4406 and we’ll tell you honestly which side of that line your kitchen sits on.
Budget $15,000-$35,000 for semi-custom replacement, or $14,000-$45,000 for a full kitchen remodel that includes cabinets, counters and finishing. The number moves with layout changes and the size of the run. Free estimate, no obligation - (844) 797-4406.
Sometimes, yes, but not always wisely. Minor drawer slide replacement and screw-hole repair is routine; swollen particleboard at the base or lifting veneer at the toekick usually means replacement is the better call. We assess all three failure points before quoting either path. Call (844) 797-4406 for a free look.
Refacing is usually faster, often completed in a couple of days, while semi-custom replacement depends on the KraftMaid build schedule and any layout changes. Either way, the plan and timeline are set before work starts. Call (844) 797-4406 to schedule.
If you’d rather have it looked at, Groundwork Construction Co. of Enterprise offers a no-pressure assessment in Enterprise - call (844) 797-4406. We’ll walk your kitchen, check the boxes, and give you a straight answer on which path makes sense for your home and how long you plan to stay.
Written by the team at Groundwork Construction Co. of Enterprise, serving Enterprise, NV.


