







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterHow to Measure a Window for Replacement in Enterprise, NV
Measure the width in three places (top, middle, bottom) and the height in three places (left, center, right), then order to the smallest number - not the largest. On the 1990s-to-present stucco homes across Enterprise, those three readings rarely match, and the gap is what sinks a custom order. A 3/8-inch difference between your top and bottom width is normal here after two decades of Mojave heat cycling. Read all six numbers, trust the smallest, and you’ll have a real measurement instead of a guess. If any three readings differ by more than about 1/4 inch, call a pro before you order: (844) 797-4406.
Here’s the catch nobody warns you about. Measuring a window sounds like a one-step job, until you find that your Mountain’s Edge home has a rough opening 3/8 inch out of square and the unit you custom-ordered won’t drop in. That’s the everyday reality for homes on the graded pads and engineered-fill lots that climb toward the Sloan and Blue Diamond foothills. Builders grade those lots to slope, not flat, and over 15 to 25 years of 105°F summers and cool winters, wall framing drifts fractionally. It matters when you’re spec’ing an Andersen or Marvin unit to the eighth of an inch.

What three numbers actually decide whether a window fits?
Three measurements matter, and confusing them is where most do-it-yourselfers get burned. Each one answers a different question: what to order, what to install into, and what you’ll actually see.
- Rough opening: the framed hole in the wall, measured stud to stud (or framing to framing), before any trim, shims, or stucco return. This is what the new unit’s frame has to fit inside.
- Frame-to-frame: the outside edge of the existing window’s frame to the opposite outside edge. This is the number most replacement orders actually key off when you’re retrofitting into an existing opening.
- Daylight opening: the visible glass area - what you see through, and what governs egress code and how much light the room gets.
The classic mistake is ordering to the daylight opening or to a single frame-to-frame reading taken at the middle. On an out-of-square opening, that average number is a lie. You want the smallest width and the smallest height across all your readings, because the unit has to clear the tightest point.
Why does the stucco return change everything in Enterprise?
Because the stucco face and the structural rough opening are two different planes, and on an Enterprise stucco home they can be an inch or more apart. When you measure flush against the stucco, you’re measuring the finish, not the frame the window actually mounts to. Order a custom window to the stucco face and you can end up with a unit that’s undersized for the structural opening - or one that won’t sit flush against the return and leaves you fighting trim and sealant.
This is where the local climate gets specific. Enterprise’s stucco takes punishing UV and extreme heat, and around the foothill-edge subdivisions that back onto open desert, the exterior detailing also has to hold up against ember exposure and defensible-space expectations. A window set proud of the stucco return, or shimmed wrong, is a leak and heat-bypass waiting to happen. On the sloped lots especially, the wall assembly, the return, and the frame all have to agree.

How much clearance do Andersen and Marvin windows need?
Custom-fabricated units from Andersen and Marvin need a shimming allowance built into the measurement - plan on roughly 1/4 inch per side, plus room for insulation and the manufacturer’s installation tolerances. That allowance is not optional; it’s how the frame gets plumb and square inside an opening that isn’t. Skip it and you’re forcing a precision unit into an imprecise hole.
So your order measurement isn’t just the smallest rough-opening reading. It’s that reading minus the shim allowance and clearance the frame maker requires. Order too tight and the window won’t go in. Order too loose and you’re packing a 3/8-inch gap with foam and hoping the trim hides it. Neither is a good outcome on a unit that costs what a custom Andersen or Marvin does.
A quick reference for the three numbers
| Measurement | What it tells you | Watch for in Enterprise |
|---|---|---|
| Rough opening | What the unit frames into | Hidden behind stucco return; may sit off the finish face |
| Frame-to-frame | Retrofit order dimension | Read at all three points, not the middle |
| Daylight opening | Visible glass / egress check | Can differ from order dimension by the frame width |
What should you check before you place a window order?
Before any custom unit is ordered, verify square and level - not just width and height. A window that measures right but sits in a racked opening won’t operate smoothly and won’t seal. Check that the opening is plumb on both sides and level across the head and sill. On Enterprise homes on engineered fill and graded pads, a sill that’s out of level by a quarter inch is common and won’t fix itself.
Then check the frame material and the frame manufacturer’s published tolerances, because a vinyl unit and a clad-wood Andersen or Marvin don’t flex the same way, and their installation specs differ. A window replacement in Enterprise runs $4,500-$15,000 depending on count, size, and material, and an impact-rated upgrade for the foothill-edge subdivisions lands at $8,000-$25,000. That’s real money, so the measurement step is where you protect it.
If you’d rather not gamble on an eighth of an inch, Groundwork Construction Co. of Enterprise treats the pre-installation measurement visit as standard, not an add-on. Our technicians bring up to 12 years of experience to the opening, verify square in person, and build the shim allowance into the order so a custom unit goes in right the first time. It’s part of how we back every job with the 730-Day Done Right Promise, and it’s the reason a re-order doesn’t eat your schedule. When you’re ready to see the full scope, look at our Windows & Doors work. Windows are one piece of the bigger picture, and if the project grows beyond a few openings, our home remodeling and construction services cover foundation to finish line.
FAQs
Measure width at the top, middle, and bottom and height at the left, center, and right, then order to the smallest width and smallest height. On out-of-square Enterprise openings, the middle reading is misleading - the tightest point is what the frame has to clear, so that’s the number you build from. If the spread is more than about 1/4 inch, have it verified on-site before ordering.
Measure the structural rough opening behind the stucco return, not the stucco face. The finish face and the framing plane can sit an inch or more apart on Enterprise stucco homes, and ordering to the wrong one is the most expensive measurement mistake we see. Take both if you can, and note the difference.
Standard window replacement in Enterprise runs $4,500-$15,000, while impact-rated units for homes near the foothill edges run $8,000-$25,000. The exact number depends on count, size, and whether you’re ordering a custom Andersen or Marvin unit. Call (844) 797-4406 for an exact quote - estimates are free.
A professional measurement is cheaper than a re-ordered custom window almost every time. A single mis-measured Andersen or Marvin unit can cost more to remake and re-install than the measurement visit itself, and on Enterprise’s sloped lots and out-of-square openings that risk is high. Call (844) 797-4406 and we’ll build the measurement into the estimate.
If you’d rather have it looked at, Groundwork Construction Co. of Enterprise offers a no-pressure assessment in Enterprise - call (844) 797-4406 for a free estimate. You can also start with our Enterprise service area page to see what we cover nearby.
Written by the team at Groundwork Construction Co. of Enterprise, serving Enterprise, NV.


